ABS线束套管

行业应用

卓益科技（广东）有限公司

汽车类

当前位置：主页 > 行业应用 > 汽车类 >

ABS线束套管

产品用途:

汽车底盘ABS线束应用

产品详情
产品性能

PUR 软管具有阻燃、耐磨性、柔软性、耐化学性等特点，替代传统轮速传感器上所使用的EPDM 保护套管，从而更好的保护ABS电线, 增加产品的使用寿命，提升汽车的安全性。
产品低VOC，低密度达到车身减重目的。软管可根据设计要求定制。

PUR tube has good properties of flame retardant, abrasion resistant, flexibility, and chemical resistant. It is designed to replace EPDM tube used in traditional wheel speed sensor and
can provide better protection for ABS wires, increase the service life and improve the safety of the car. Low VOC is released by the PUR tube and low density can achieve the car weight reduction purpose.
The tubes can be designed as per customer’s requirement.

序号	Description规格	Tolerance(mm) 内外径公差	Wall thickness(mm) 壁厚	Tolerance wall thickness(mm) 壁厚公差
1	PUR1.6*3mm	±0.15	0.7	± 0.15
2	PUR3*5mm	±0.15	1.0	± 0.15
3	PUR3.5*6.1mm	±0.15	1.3	±0.15
4	PUR4*6mm	±0.15	1.0	± 0.15
5	PUR4.5*7.1.mm	±0.15	1.3	± 0.15
6	PUR5*6mm	±0.15	0.5	± 0.15
7	PUR5*8mm	±0.3	1.5	± 0.15
8	PUR6*7mm	±0.3	0.5	± 0.15
9	PUR6*8.6mm	±0.3	1.3	± 0.15
10	PUR6*9mm	±0.3	1.5	± 0.15
11	PUR6.5*9mm	±0.3	1.25	± 0.15
12	PUR6.5x9.7mm	±0.3	1.6	± 0.15
13	PUR7*9.7mm	±0.3	1.35	± 0.15
14	PUR7*10mm	±0.3	1.5	± 0.15
15	PUR7*10.7mm	±0.3	1.85	± 0.15
16	PUR7.5*10.1mm	±0.3	1.3	± 0.15
17	PUR7.5*10.7mm	±0.3	1.6	± 0.15
18	PUR8.0*10.7mm	±0.3	1.35	± 0.15
19	PUR8.5*11.1mm	±0.3	1.3	± 0.15
20	PUR9**10.4mm	±0.3	0.7	± 0.15
21	PUR9*12mm	±0.3	1.5	± 0.15
22	PUR10*12.7mm	±0.3	1.35	± 0.15
23	PUR10.1*11.3mm	±0.3	0.6	± 0.15
24	PUR13*5.7mm	±0.3	1.35	± 0.15

*Special sizes on request 其它尺寸按需订制

Description 性能	Test Method 测试方法	判定标准 Typical value
Shore A hardness 邵氏硬度A	DIN ISO 7619-1(3S)	85(+/-5)
Tensile strength, 拉伸强度	TL 529-2008 1 6.2 & DIN 53504:2009	≥30N/mm2
Dimension change rate, 尺寸变化率	ES-2U5A-1A263-AA-2005 6.4 ，170℃，24h	≤10%
Abrasion, mm³耐磨损	ES-2U5A-1A263-AA-2005 6.9 &ASTM D4060-2014	≤0.1%
Flammability 燃烧测试	ES-2U5A-1A263-AA-2005 6.10 & ISO 3795:1989	≤100mm/min
Low temperature resistance 耐低温	ES-2U5A-1A263-AA-2005 6.5 ，-40℃，4h	No deformation and no break 无变形或开裂
High temperature 高温测试	GB/T2423.1-2008	No deformation and no break
Temperature resistance 耐热性能	ES-2U5A-1A263-AA-2005 6.8 ,125℃，3000h	No deformation and no break 无变形或开裂
Thermal aging test 热老化测试	ES-2U5A-1A263-AA-2005 6.3 ，125℃，400h	≥35%
Odor 气味	Refer FLTM BO 131-03 (2017) Sampling volume：3L，type：A ，Size：100cm²	WSS-M99P2222-F1 (2017) ≤3.0
VOC	Refer FLTM BZ 108-01( 7/2/2018)VOC, (HPLC/DAD) (TDS/GC-MS)	/
Nebulization 雾化	Refer SAE J1756(2006) Reflection method ：heating at 100 ℃ /3 hours . condensing temperature 21℃，Drying time 16 hours	Based on WSS-M99P2222-F1(2017) Reflection method 反射法：≥70，无油膜、液滴、结晶状沉积物
Density 密度	TL 529-2008 1&DIN EN ISO 1183-1:2013 Method A	1.095g/cm3
ELV	GB/T 30512-2014	铅(Pb)≤100ppm、镉(Cd)、汞(Hg)、六价铬(Cr6+)、多溴联苯（PBBs）、多溴二苯醚（PBDEs）≤1000ppm
RoHS	Refer RoHS Directive2011/65/EU and amending Annex directive EU 2015/863	铅(Pb)≤100ppm、镉(Cd)、汞(Hg)、六价铬(Cr6+)、多溴联苯（PBBs）、多溴二苯醚（PBDEs）、DBP、BBP、DEHP、DIBP≤1000ppm
Short term aging 短期老化	ISO 6722-1:2011 150 ℃，240 h→-25℃，4h	No crack and no break
Elongation at break 断裂伸长率	TL 529-2008 1 6.2 & DIN 53504:2009	≥400%
IR 红外光谱	GB/T 6040-2019	≥95%
Impact test抗冲击试验	ISO 6722-2011	No crack and no break
Ozone resistance 耐臭氧试验	SMTC 3 261 004	'0 level , No crack
Chemical resistance 耐化学试剂	SMTC 3 800 001-20109（V1） 10.2	No break
Hydrolysis resistance 耐水解	500h storage in istilled water at 85℃ for 500h 85℃蒸馏水中存放	No crack and no break
Crushed stone impact test碎石冲击试验	SAE J400-2012	No break and no scratch on the tube surface 套管表面无明显损坏、磨痕

行业应用

卓益科技（广东）有限公司

产品用途:

相关产品